Tag: Learn To Fly

-->

How Flying Critical Incidents Can Occur

Posted on by Kai

When an aircraft flying under Visual Flight Rules (VFR) enters Instrument Meteorological Conditions (IMC), flying critical incidents can sometimes occur. In most cases, this is due to reduced visibility or inadvertent entry into clouds. Both of which happen because of the loss of the natural horizon.

Unfortunately, such flying critical incidents have cost the lives of many pilots.

You hope it will never happen to you

Before I began my pilot journey, I always seemed to find the time to read unfortunate accident reports where a non-instrument rated pilot on a VFR flight enters IMC. It is even more unfortunate to realise that many of these incidents become fatal accidents. The more I’ve read, the more I’ve tried to make myself believe, ‘It will never happen to me!’

For non-pilots, all of these accidents seem preventable. Reading the Terminal Area Forecast (TAF) and good weather knowledge are all valid and effective strategies to combat any similar occurrence from happening. However, today I will write about a time when this happened to me on a training flight, nonetheless with an experienced instructor on board.

The importance of sharing stories

Before undertaking the task of writing it, I had been wondering about whether or not I should really share my story. However, I made the decision to do so knowing it could help educate other pilots and student pilots about when flying critical incidents can occur.

Cloudy conditions and lower visibility

It was a very cold morning after a cold front came through the day before. I checked the METAR of Hong Kong International Airport and the forecast indicated cloud covers clearing and rising to 2500 feet with 9 kilometres of visibility. However, as I arrived in the flight operations office, we received PIREPs from other pilots of temporary visibility reduction to an estimate of fewer than 3 kilometres near the high ground. I knew this could become an issue upon exiting the airfield area into the training area via a gap in the mountains.

The aircraft from previous slots were rocking the circuit and about to finalise their return. Skies above Shek Kong Airfield were clearing and let in some warm sunlight. However, the area towards the exit route (Kadoorie Gap) into the training area was still rather cloudy. I saw clouds on the other side of the mountains and thought this could really be an issue for our flight today – we had some instrument flying planned.

Climbing to 1500 feet

My instructor had nearly 40 years’ experience in the UK as an aerobatic pilot and warbird pilot. He also holds an Instrument Rating – Restricted on his CAA license – although on his Hong Kong license he does not hold such rating. Even so, his instructor rating allows him to teach basic instrument flying and tracking. On this day, despite the clouds, I put my trust in his judgement and was well aware of his capabilities since we had flown together numerous times.

We taxied out to the runway after our run-up checks, only to notice something very strange. Our slot was supposedly fully booked out with our entire fleet expected to fly. However, there was no action on the aircraft apron. I recall looking to my right as I prepared to shift into full power for takeoff and witnessing all the aircraft sitting idly, waiting for the weather to clear. Still, I thought there was no time to waste and we took off.

We climbed to 1500 feet and tracked towards the exit. As soon as we switched frequencies for traffic information service we heard a rescue helicopter saying, “Visibility deteriorating to less than 3000 meters.” I wasn’t sure where the helicopter was, but in retrospect, it really should’ve been the warning to turn back. We pressed on and exited out of the mountain gap and went on to “the other side,” where all the nasty clouds were, maintaining 1500 feet all the way through.

Scary in-flight sights

As soon as the mountains disappeared from my peripheral vision, my instructor and I realised that visibility was not 9 kilometres, as we had initially projected, and I could only see what was in front of us by looking downwards.

The only visibility I had was of the ground below, including the roads, trees and buildings of Tai Po. I looked back and realised that our only escape route back to the airfield would be obscured if we kept going. Just as I was about to turn back, it became apparent that my instructor had the same idea in mind. “Bring us back,” he said.

Returning through the mountain gap

The direction indicator on that particular Cessna 172 was somewhat defective. This meant I started my timer on my watch and began a rate one turn to the left. I timed for 1 minute, which at 3 degrees a second would be a full 180-degree turn. Fortunately, the mountain gap remained in view this entire time and I instinctively throttled up to return quickly. We were pushed even lower as we entered the airfield airspace, finally descending to 1300 feet. It was very uncomfortable watching the mountains on either side of me come so painfully close.

Lessons learnt

Of course, we were fortunate that despite this being a VFR into IMC incident. The visibility was still sufficient for a safe turn-back manoeuvre.

Among the contributing factors to the success of this was the expertise of my instructor, who holds a restricted instrument rating in the UK, and the fact that at this time I had already completed an hour of instrument flight training. A serious lesson in how flying critical incidents can occur.

After landing, and during the debrief, we narrowed the causes down to the ‘get-there-itis’ that occurred as a result of wanting to squeeze more instrument flying time in for me and also the fact that my instructor was instrument-rated and we put such confidence in his expertise. In retrospect, we shouldn’t have even left the ground in the first place.

This flying incident is proof that pilots with any amount of experience can be sucked into this veil of complacency. They then can make decisions which go against rational and safer judgement. It is an incident my instructor and I will both go on to remember.

Safe flying everyone!

Flying-Critical-Incidents
When an aircraft flying under Visual Flight Rules (VFR) enters Instrument Meteorological Conditions (IMC), flying critical incidents can occur.

Thanks to LTF student pilot Howard Lau for contributing this article on how flying critical incidents can occur. For information on our flying courses, email [email protected] or go to https://drift.me/learntofly/meeting to book a meeting and school tour. You can also get more handy flying tips by clicking below and subscribing to our YouTube channel!

Learn-To-Fly-Melbourne-Youtube-Subscribe-Footer

Five Benefits of Choosing a Part 142 Accredited Flying School in Australia

Posted on by Kai

Learn to Fly Melbourne is excited to announce that we have become a Part 142 accredited flying school operator under the Civil Aviation Safety Regulation (CASR).  This results from our new partnership with Australian Pilot Training Alliance (APTA).

Over the past few years, pilot licencing regulations in Australia have been reorganised and redeveloped. They have changed from older criteria to reflect a more global perspective regarding pilot licencing and standards.

This move may not be obvious to the customer or pilots. Yet it has given rise to new terms and extra regulations and definitions. Flight training organisations across Australia now have two main paths that they can follow when seeking to earn their air operator certificate: Part 141 and Part 142.

Why choose a Part 142 accredited flying school in Australia?

Less than 5% of flight schools in Australia have received the advanced Part 142 flight training qualification. This accreditation means that we can continuously expand our flight training operation to reflect the highest industry standard.

There are numerous benefits for students, pilots and instructors who fly at a Part 142 accredited flying school.

1. CASA Approved Syllabus

Part 142 organisations must provide a Civil Aviation Safety Authority (CASA) approved syllabus of training. This CASA approval caveat for Part 142 initiates the necessity for additional oversight of training programs within organisations.

This results in further internal development and higher levels of safety and training. That subsequently improves standards not just within individual organisations but also within the wider aviation community. Part 142 flying schools benefit from a consistently higher level of governance and checks from CASA.

2. Advanced Flight Training

Our comprehensive CASA approved flight training syllabus includes the following new courses and types of flight training:

Integrated flight training for Private Pilot Licence (PPL) or a Commercial Pilot Licence (CPL) courses

Multi-Crew Pilot Licence (MPL), Air Transport Pilot Licence (ATPL) and Flight Engineer Licence

Multi-Crew Cooperation (MCC) training

Contracted recurrent training and checking

Being able to offer integrated flight training is one of the major points of difference between the Part 141 and Part 142 qualification. What it means for students earning their CPL is that they can cut down their flight training hours from 200 to 150 – a 50-hour flight training discount when compared with Part 141 flying schools.

3. Increased Cost Effectiveness

Integrated flight training – Our 150 hours Integrated CPL syllabus which blends practical flying and theory-based training compared with the 200 hours CPL syllabus offered by other Part 141 schools – is just one of the ways that the Part 142 qualification is extending our commitment to provide students with cost-effective flight training.

4. Internal Training & Checking

Part 142 flight training organisations are required to have a professional development program for all personnel and flight instructors within the school. They must also have a quality assurance manager to ensure ongoing high standards.

This conditional improvement of know-how and standards applies not just to students, but trainers and instructors alike who continually develop their own skills within an organisation.

5. Enhanced Safety

All Part 142 flight training organisations must have:

A Safety Department & Safety Management System

A CASA Approved Safety Manager & Deputy Safety Manager

A Risk Management System

Regular safety meetings, audits and reviews

Safety oversight globally has become one of the main areas of focus in not just maintaining high aviation standards, but improving safety as a whole. This is most visible in the incorporation of formalised procedures for Safety Management Systems.

These systems actively monitor standards and safety within training organisations by promoting an ongoing awareness, attitude and approach towards threats and risk on a daily basis. The net result for pilot candidates is that these systems set a higher standard for all who come in contact with them, making not just the individual pilots safer, but organisations and the industry as a whole.

We are excited for students to enjoy the increased benefits of training with us now that we have achieved the CASA approved syllabus Part 142 qualification.

Part-142-Accredited-Flight-School
Students enjoy some fantastic benefits training with a Part 142 accredited flying school.

Want to learn more about the benefits of flying with a Part 142 accredited flight school? Email [email protected]. You can also visit https://drift.me/learntofly/meeting to book a meeting and school tour.

Learn-To-Fly-Melbourne-Youtube-Subscribe-Footer

Pilot and Aircraft Safety at Learn To Fly

Posted on by Kai

At Learn to Fly, pilot and aircraft safety is and always will be our number one priority. It is the cornerstone of our operation, and we strive to maintain a positive and transparent safety culture.  We continue to uphold an impeccable safety record as conveyed on the Recreational Aviation Australia (RAAus) Accident and Defect Summaries. 

The safety culture at Learn to Fly acknowledges that flying and flight training involves risk. It’s vital that students and instructors alike are educated about these risks and the processes involved in risk minimisation.

See how we carry out pilot and aircraft safety in our flight training operations at Learn To Fly.

Aircraft Maintenance

Each aircraft requires maintenance checks for every 50 and 100 hours of flying. All scheduled maintenance is planned in advance. We will never undertake any flights or flight training on planes requiring maintenance.

Pilots and engineers can write up a defect on the aircraft’s Maintenance Release (MR) at any time. For serious defects, the aircraft will immediately become unserviceable and simply will not go flying until maintenance is completed.

The Maintenance Release is required to be signed by a pilot (instructor or pilot certificate holder) before the first flight of each day to ensure that the aircraft has passed the daily inspection requirements and is suitable to fly.

Instructor Qualifications

Pilot and aircraft safety for us also means company standards require that instructors at Learn to Fly be well-trained. We will only employ instructors who we are confident, focused, alert and ready to respond immediately to any potential situation where the risk outweighs the learning opportunity.

Based on the current guidelines, all of our flight instructors are at an RAAus senior instructor level. This rating can only be achieved if the pilot accumulates certain flight training experiences and passes a flight test that is conducted by external RAAus certified flight testing officers.

Some of our students may become junior instructors when they graduate. However, it is a compulsory requirement that they are supervised by senior instructors when they work at the school.

In addition to this, our chief flying instructor (CFI) actively supervises all flight training operations and consistently checks training records and documentation. This ensures that Standard Operating Procedures (SOPs) are complied with for both instructors and students. SOPs compliance is checked at various times. This is usually by attending flights with students to confirm SOPs are maintained, and ensuring all instructors have current qualifications.

Flight Training

We ensure a safe learning environment every time.  A student will not fly if the weather is not suitable for that particular lesson. For solo flights, these standards will be even stricter and reflect considerations such as turbulence, wind speed, daylight, student’s abilities etc so that we can provide

Before all flights, the aircraft will be thoroughly inspected. This ensures all controls are functional, check for obvious damage to the engine, airframe or structure before any flight is to take place. After engine start and prior to takeoff further checks are carried out as per the SOPs. This is recommended by both the aircraft manufacturer and in the aircraft’s Pilot’s Operating Handbook (POH) to further assure a safe and efficient flight takes place.

Each student’s flights are recorded in detail. Instructors will rate their performance to make sure students reach the standard or competency of that particular lesson. Students who do not meet these standards or competencies will have to redo the lesson sequence until this standard is met. Within the school, we have systems in place to cross-check and ensure that all training records are completed and updated in a timely manner.

Briefings are always done properly and consistently before and after each flight. This ensures that students are both aware of what they are going to do, and of the specific standard that is required for that particular lesson.

Prior to solo flights, instructors will double-check to make sure the students have all the required documents such as a medical certificate, student pilot licence etc. Training records must also show they have achieved all the necessary competencies prior to undertaking any solo operations.

Creating a Pilot and Aircraft Safety Culture

Further to the priorities and procedures outlined, we maintain our own Risk Management Plan and Safety Management System. This enables us to further minimise the potential risks associated with flight training. Despite this comprehensive system, we must not think that we are infallible. We encourage all of our staff and students to form a habit of looking, learning, and discussing potential risks we see as part of our normal day to day operation. This attitude allows us to evolve and update our systems regularly. That then helps to ensure a safe operating culture persists within the Learn To Fly organisation and group.

We encourage instructors and students to go through appropriate channels to advise safety concerns within or outside of our operation.

We believe that technology as a communication tool has great potential to assist safety operations. Flight training software can provide updates on aircraft unserviceability or if an aircraft may need to be grounded; through to communicating safety concerns or topics that instructors or students raise within the organisation.

Exceeding Expectations

We aim to have higher safety standards than other flight schools in Australia.

On top of the Public Liability Insurance and the RAAus Member Liability Insurance, we cover an additional A$5 million in Liability Insurance for all of our students.

We only buy brand new RA-Aus aircraft so we can be certain of the maintenance history for every plane.

All RA aircraft in our fleet is equipped with Rotax engines which have an outstanding reputation and operational safety history.

At Learn to Fly, we believe all these extra steps – combined with the safety culture exhibited by our individual pilots, instructors, and the student group – will allow us to go a long way in providing an extra margin of safety.

Aircraft-PreFlight-Safety

Want to fly with us? Email [email protected]. You can also visit https://drift.me/learntofly/meeting to book a meeting and school tour.

Learn-To-Fly-Melbourne-Youtube-Subscribe-Footer

What is Threat and Error Management in Aviation?

Posted on by Kai

Threat Error Management (TEM) in aviation is a term that has commonly been associated with airline operations. But it also extends to all other aspects of aviation. TEM is all about being a safe and well-prepared pilot.

The definition of Threat and Error Management in aviation 

Threat Error Management (TEM) has been defined by various institutions. The Australian authority Civil Aviation Safety Authority (CASA), defines it as:

‘The process of detecting and responding to threats and errors to ensure that the ensuing outcome is inconsequential – the outcome is not an error, further error or undesired state’.

It wasn’t always called TEM

The term has evolved over time from Cockpit Resource Management (CRM) to Crew Resource Management (again CRM), to its current form as TEM.

Although these big words and terms sound noteworthy, you most likely won’t come to grips with what they are really about or how much of an impact they have on a pilot during a flight without exploring them in detail through study and practice.

Its impact extends beyond aviation

While TEM was first adopted by the airline industry, its importance for all of us should not be underestimated. TEM has impacted of all kinds of industries in a multitude of ways.

Threat and Error Management processes and practices have become the benchmark when approaching tasks and activities in a range of professions, including our flight training and other standard aviation procedures.

TEM gives us perspective on perception

Each of the key concepts in TEM relates to a specific aspect of a total process, and all are aimed at handling a particular threat.

What is a threat? Furthermore, what is a threat to you?

In many cases, this threat can be different to the one which is commonly perceived.

Threats can come in many forms, such as environmental. The weather, or other factors that may seem inconsequential such as:

Flying in a different aircraft compared to your usual one

Having a change of instructor on the day

Preparing adequately for your flight

Not having enough sleep the night before

All of these are considered threats as they can have an impact on the outcome of any flight.

Errors become easier to manage

Beyond the threats is the resulting error. Some errors may result in a further error, varying in size but depending on how we handle it may or may not impact on the safety of the flight. Ultimately, this aspect relies heavily on how the management of that error is addressed.

As pilots, we are the last line of defence when considering errors and, therefore, safety. The key responsibility to prevent this error from having an outcome or impact on the flight and placing one’s aircraft in an ‘undesirable state’.

This management should not be underestimated because a significant or undesirable outcome places one in a position that none of us would like to contemplate, irrespective of the size or aircraft type that we are operating.

TEM Invites closer analysis of safety

The question that arises is what should we do when handling threats and errors each time we go flying? The answer may vary, however, we should actively look around us and consider any factor that may be perceived as a threat.

Beyond this, consider what error could arise from this and how as an individual you would manage or handle this situation. Only then with constant attention, proactive discussion and consideration of factors around us will we improve our skills and awareness towards becoming better and potentially safer pilots of the future.

See how Threat and Error Management in aviation is discussed in one of our flying lessons on YouTube below. Don’t forget to subscribe for more great flight training content!

Want to fly with us? Email [email protected]. You can also visit https://drift.me/learntofly/meeting to book a meeting and school tour.

Learn-To-Fly-Melbourne-Youtube-Subscribe-Footer

Final Flight Departure Procedures: Flight Departure Processes Part 3

Posted on by Kai

In this blog series on flight departure processes we have covered engine starts, taxi checks, run-up checks and more. Now it’s time to run through the final flight departure procedures and take to the skies!

Use the TMPFISCH acronym

The proper acronym that applies whenever holding short is TMPFISCH, and it is what I usually use for my operations here in Hong Kong. It goes like this:

T – Trims set to the appropriate take-off position

M – Mixture rich, master on and magnetos on both

P – Primer in and locked (or fuel pump off)

F – Fuel is sufficient for the coming flight and flaps are set

I – Instruments’ Ts and Ps are in the green range

S – Switches (landing and strobe lights on)

C – Controls full and free

H – Hatches secure and harnesses secure

When you do your controls part of this departure check, make sure your box the controls. That means to move the controls in a movement of a box and ensure you have still got adequate freedom of movement. You might have a mile-long taxi, and something might have jammed the controls. Never skip this check as part of your final flight departure procedures.

Deliver your safety brief

You can do the EFATO brief (Engine Failure After Take-Off ) at any stage before the take-off, but I typically do it after run-ups. A typical brief should describe the actions that need to happen in the event of an engine failure at particular stages of the flight, such as:

During take-off

After rotation

Below 200 feet and with runway remaining

Above 200 feet with no runway remaining

Above 700 feet.

The brief goes something like this:

“If we have an engine failure on the ground, we stay on the ground. If we have an engine failure below 200 feet, we land on the remaining runway. If we have an engine failure above 200 feet, we land straight ahead or 30 degrees to the side. If we have an engine failure above 700 feet, we will turn back to find runway X.”

On a standard Cessna or Sling, 700 feet is plenty for a runway turn-back manoeuvre. However, during the turn back you MUST lower the nose to maintain airspeed and limit the angle of bank to 45 degrees. Never attempt a runway turn-back if an engine failure occurs below 700 feet!

Ready to go

You are lined up on the runway, and ready to take to the skies. It’as always an exciting moment for any pilot. However, discipline must be maintained during the final flight departure procedures.

Ensure you are on the correct runway by looking at your directional gyro, which will indicate the proper runway heading. It’s also a good practice to cross-check this reading with the magnetic compass as well. After that, you should triple-check with making sure that the runway numbers are indeed the intended runway. Everything checks out? Good.

Time to fly!

Now the take-off roll can begin. Ensure that your heels are on the floor and that you are controlling rudders only with the balls of your feet; this will ensure that you do not inadvertently apply the brakes! After you complete this, you should use full power – smoothly but with purpose – and count three, one-thousands before going all the way with to full strength.

After full power is applied, check on the RPM. They should be reading at or above the stated minimum static full-throttle RPM. At this stage, you should also check the oil temperatures and pressures and ensure that these are still sitting within the green range. Finally, you should check to ensure that the airspeed indicator is ‘alive’, meaning that it is indicating an acceleration.

At rotation speed, gradually apply back pressure and lift the nose wheel off the ground, allow the aircraft to fly off the runway and then adopt a Vy (best rate of climb) attitude to ensure maximum climb performance. Look outside! Once you are above 300 feet AGL and obstacles are cleared, move the flaps to up and auxiliary fuel pump (if applicable) to off. You should once again check the oil temperatures and pressures.

The result of following the correct final flight departure procedures? A smooth take-off, followed by another safe and beautiful flight!

Thank you to student pilot Howard Lau for contributing this great series on flight departure procedures.

IMSAFE-For-Pilots
With the final flight departure procedures done, it’s time to fly!

Find out what it feels like to take to the sky! Email [email protected] or visit https://drift.me/learntofly/meeting to book a meeting and school tour.

Learn-To-Fly-Melbourne-Youtube-Subscribe-Footer

Flight Pre-Departure Checks: Flight Departure Processes Part 2

Posted on by Kai

In Part 1 of our flight departure processes series, we laid the groundwork to set ourselves up. In this post, we will go through your flight pre-departure checks. This includes engine starts, taxi checks and run-up checks. Following these checks we’ll be heading to the runway.

Perfect priming

Let’s start our flight pre-departure checks with the most important thing. Safety. Crack open the window and say, ‘CLEAR PROP’. Make sure you give people time to stand clear and scan the area before you move on with your other procedures.

Next, place one hand on the throttle and start cranking the starter, but for no longer than ten seconds each time. If the engine does not fire within 10 seconds, stop cranking right away and wait a minute so the starter motor can cool down. Try some light priming when you’re ready to have another go—it works wonders.

When the engine fires, release the starter promptly. If you’re flying a plane with a fuel-injected Lycoming engine, adjust the mixture to full rich.

Green means go

After a successful engine start, you will need to check that the oil pressure is rising (or has correctly risen) into the green range. This is crucial because oil pressure indicates whether metal components in the engine are sufficiently lubricated.

If oil pressure is not within the green range, shut the engine down immediately and report this to the engineer.

As long as the pressure looks good, you can raise the flaps (if left down after pre-flight), turn on the taxi and navigation lights, and turn on the avionics master switch. Only now should you don and adjust your headsets.

Eyes forward

When taxiing, you should aim to minimise the time you spend with your head down – literally so you don’t bump into anything.

It has become normal for pilots to use GPS devices and iPads (used to run apps like OzRunways) in the cockpit. It is ironic, therefore, that when we attempt to program devices while taxiing we put ourselves at risk of having an accident.

The only exception I make to this rule of my flight departure process is to check the turn instruments. I like to quickly glance down and ensure that:

The slip ball is deflecting properly

The turn coordinator is indicating correctly

The direction gyro turns in the proper direction

The attitude indicator stays erect

The magnetic compass turns in the proper direction.

Remember the CIGAR acronym

I like to do my run-up checks using the acronym ‘CIGAR’. Here is how it works:

Controls – full and free and control surfaces deflect correctly

Instruments – all in the green range, the ammeter is charging and the suction is in the green range

Gas – check the mixture and fuel selector

Airframe – secure the canopy, doors and windows, and make sure your parking brake is on

Run-up – set the correct run-up RPM, check the brakes, check the magnetos, note when the RPM drops (on the Sling with the 912iS engine, one must check that both engine fuel pumps are working), pull the throttle to idle and ensure the engine does not seize at idle

After the run-up, the engine should be set to the ground idle speed as recommended in the POH.

Thank you to student pilot Howard Lau for contributing this great series on flight departure procedures. Stay tuned for the third and final instalment coming soon, as we head to the runway!

Flight-Pre-Departure-Checks
CLEAR PROP! Safety comes first when completing your flight pre-departure checks.

Find out what it feels like to take to the sky! Email [email protected] or visit https://drift.me/learntofly/meeting to book a meeting and school tour.

Learn-To-Fly-Melbourne-Youtube-Subscribe-Footer

Flight Departure Processes: Part 1 of 3

Posted on by Kai

With so many other things in life, it’s easy enough for you to just remember something once you know it. Then it’s no problem to repeat it. Like driving. But flying is different. There are checklists and acronyms (and more checklists) for a reason. There are far more safety considerations when you are flying, and following the right flight departures processes will help to ensure you have a smooth and safe flight, every time.

Walk the walk

A successful and safe flight begins before you even turn on the master switch. It all starts on the tarmac as you approach the aircraft. Your flight departure processes should involve asking yourself lots of questions:

Are the tie-downs done properly?

Are the tyres inflated correctly?

Is there any pink hydraulic fluid around the aircraft?

Is there any blue fluid around the aircraft reminiscent of Avgas?

It has been scientifically proven that asking yourself questions is the most effective way to stay in the loop of information.

Feel the wind

You should not only ask yourself about the aircraft or about the ‘now’ but also ask questions that will bring into effect a successful take-off. Personally, I like to ask myself these:

Should I use flaps or not?

What technique will I use for these conditions? Short field or normal?

Should I delay my rotation for density altitude, load or gusts?

What crosswind correction should I be using during taxi and initial roll?

These questions really are the basis for me completing smooth and safe flight procedures. They help me make sure I’m always ready to respond to new information. On that note, try to make sure you always pay attention to your surroundings. Feel the wind, look at the windsock, listen to the wind and feel the temperature on your skin. Forming attentive habits and looking out for these cues will allow you to prepare for a better flight.

Take it easy

After a normal interior and exterior pre-flight check has been completed, and the aircraft is confirmed to be in safe working order, we can proceed to the engine start. My secret tip is don’t rush!

I’ve had the fortune to fly with the training captain of a major airline in Hong Kong, who is also a tailwheel aircraft instructor and aerobatic pilot. He said these wise words I will never forget, ‘Don’t rush because if you rush you will kill yourself one day.’ I could not believe the severity of his words given his experience in aviation! Needless to say, I listened to his advice.

Get ready for ignition

Before I start the engine, I like to plug in the key, and with the master switch off, I rotate the key to start and then release it. The key should immediately snap back to the both position. This is a simple pre-start ignition check that I learned during my time as an aircraft maintenance intern in Hong Kong.

What this check does is make sure that the starter motor does not engage when the master switch is off, the key locks into position properly and the spring mechanism works.

Prepare the cabin

With the pre-start ignition check completed, I check the cabin. This is when you should adjust your harnesses and seats to your satisfaction, and keep a window or the canopy open. After ensuring that the propeller area is clear, flip on the beacon light switch and the master switch.

Look at your ammeter—it should show a discharge. Check your oil temperature to gauge the amount of priming required or (if it’s the Rotax 912ULS equipped Sling 2 or the Bristell at Learn to Fly) the use of choke. Ensure all circuit breakers are in and the avionics master switch is off.

Wait for it

One of my pet peeves at this stage is pilots who don their headsets before the engine has started. What if someone was trying to get your attention about an unfolding emergency? With the headset on, you wouldn’t be able to hear them. Instead, remove the headset from the dashboard and put it on your lap so you can have maximum visibility out of the windscreen.

An unwritten rule

Set the fuel selector in accordance to the POH and prime as required. After priming, ensure the primer pump is in and locked or, alternatively, that the auxiliary fuel pump is off. If the plane has a fuel-injected Lycoming machine, check that the mixture is set to full rich. If you’re ever in doubt, start with no prime. This will avert the possibility of flooding the cylinder heads due to excessive priming.

Thank you to student pilot Howard Lau for contributing this great series on flight departure processes. Stay tuned for the next part, where we run through flight pre-departure checks.

Flight-Departure-Processes-Female-Pilot
Getting your flight departure processes right ensures the safest start to your flight.

Find out what it feels like to take to the sky! Email [email protected] or visit https://drift.me/learntofly/meeting to book a meeting and school tour.

Learn-To-Fly-Melbourne-Youtube-Subscribe-Footer

6 Ways to Maintain Pilot Proficiency and Safety

Posted on by Kai

Once you achieve the Recreational Pilot Licence (RPL) or Private Pilot Licence (PPL), as well as any endorsement or rating on top of that, you must apply yourself to the tasks required to maintain pilot proficiency and safety.

Commercial pilots do this by flying a lot of hours, but unfortunately, a lot of RPL and PPL pilots don’t have this luxury, which means their skills diminish over time. Here are six ways to make sure this doesn’t happen to you.

1. Know yourself

For the sake of common sense and for safety, a pilot should keep analysing their performances and keep practicing. More than anything, they should be aware of their limitations. It’s your responsibility to assess where you’re with your skills and knowledge at all times and compare it with where you aim to be. If you ever find there’s room for improvement, take the time before your next flight to prepare for it.

2. Show safety in your attitude

Flying is an attitude and a way of thinking. It’s about one thing above all else, and that is a concern for safety. To maintain pilot proficiency and safety means turning up focused for the flight. It’s what will keep you on track to maintain your relevant skills and qualifications down the line. Even better is if you can start putting this attitude into effect while you’re still on the ground.

3. Watch the weather

You can download the relevant weather from www.bom.gov.au or NAIPS on a regular basis to see how it is expected to develop during the course of the flight. When you know what to expect from the weather you will automatically start solving related problems prior to the flight. It will set up your in-flight decision making for success and quicken your response time when adjustments are called for.

4. Refresh your knowledge

Maintaining pilot proficiency and safety requires a high level of skill. It’s about doing what you can when you’re not physically in the cockpit, and preparing yourself for the next flight. For example, when a pilot doesn’t fly a particular aircraft for some time, particularly if it is a complex aircraft, they should study critical aspects such as speed, RPM settings and emergency procedures before flying again.

5. Seek out other pilots

Refreshing your accumulated knowledge in aviation should always be self-directed, but this doesn’t mean you can’t reach out to other pilots to get support and advice. If you’re in doubt, ask an instructor at your flying school to test you on the spot or give you ideas about who to contact.

Although things like a check flight will normally be conducted by the flight school automatically, you must be disciplined throughout your training, so that you can later recognise when this is necessary and follow through.

6. Build up your ratings and endorsements

Another way to maintain your proficiency is to go and get a new endorsement or rating. This can take your flying to a whole new level and benefit all areas of your competency to fly. While this training will add to your existing skills, it will also force you to go over what you have learnt already.

Bonus tip! Enjoy the ride!

Pilots have no shortage of things to learn and all of this needs to be maintained in the long term. Hopefully, your competency rewards you with better, easier flying experiences over time. Many pilots come to love the many small details in their regular procedures that allow them to exert an amount of control over a flight, which changes the technical success of every journey.

Pilot-Proficiency-and-Safety
Once you have achieved your licence, you will need to continue to to maintain pilot proficiency and safety.

Want to fly with us? Email [email protected]. You can also visit https://drift.me/learntofly/meeting to book a meeting and school tour. For more great flying tips and the latest flying videos, click below and subscribe to our YouTube channel!

Learn-To-Fly-Melbourne-Youtube-Subscribe-Footer

Training Beyond the Private Pilot Licence (PPL)

Posted on by Kai

After completing your Private Pilot Licence you might wonder, “what’s next?” As strange as it may sound, many pilots are still keen to do more training after achieving their initial goals. Realistically, if you want to fly regularly or as a job, learning is ongoing. Let’s take a look at training beyond the Private Pilot Licence.

Fly more aircraft types

Why limit yourself to flying just the one aircraft type? Why not fly aircraft that are bigger, faster, have more than one engine, or maybe even can land on water?! There are ratings and endorsements that can open up a whole new range of aircraft to you. These include a Tailwheel Undercarriage Endorsement, Multi-Engine Class Rating, and more.

Having the capability to fly more aircraft types increases your skill level, and gives you a lot more options when organising recreational flying trips.

Tailwheel-Training-PPL
A tailwheel endorsement opens up a range of new aircraft options.

Fly at night

Flying at night is an amazing experience. If you live near a major city, seeing the sparkling lights from above is absolutely spectacular. Completing a Night Visual Flight Rules (VFR) course. will allow you to fly at night, in otherwise good weather and visibility conditions.

Fly in more weather conditions

One of the most important areas of training beyond your Private Pilot Licence will allow you to plan and conduct flights in far more weather and light conditions. Instrument flying is a great skill to have, not just for your own flying abilities, but for added convenience when planning flights. It allows you to fly in inclement weather conditions, cloudy conditions, and at night.

Flying under Visual Flight Rules (VFR) alone can be quite restrictive, especially in areas with changeable weather like Melbourne. A Private Instrument Flying (PIFR) course can be customised to your needs, making it a great option.

Flight activity endorsements

There are some seriously fun flight activity endorsements that you can add to your repertoire.

Formation flying is an experience that even the most seasoned pilots get a huge thrill from. Taking off, flying, performing manoeuvres and landing with another aircraft right next you is surreal. Flying in formation is also a very good tool for honing your precision skills, with precise control movements required for accuracy.

Another popular endorsement is aerobatics and spinning. Aside from being a huge amount of fun, this type of flying is again great for your skillset. Knowing how your body reacts and how you can recover from high G situations and unusual attitudes is actually very important.

As you can see, there is no shortage of options for training beyond your Private Pilot Licence. Additional endorsements will enhance your ability to get the most out of your PPL, and also help you to keep your skills sharp.

PPL-Formation-Flying
A formation flying endorsement is an exciting way to hone your precision control input skills.

Find out about our extensive range of ratings and endorsements for PPL holders! Email [email protected]. You can also visit https://drift.me/learntofly/meeting to book a meeting and school tour. For more great flying tips and the latest flying videos, click below and subscribe to our YouTube channel!

Learn-To-Fly-Melbourne-Youtube-Subscribe-Footer

6 Ways to Improve Flight Training Efficiency

Posted on by Kai

We are always thinking about ways to help our students get the most out of their flight training course. We believe it’s so important for students to be able to motivate themselves as they work through their training hours. Part of this is applying efficient learning tactics that keep everything progressing at a healthy rate. We are always looking for ways to improve flight training efficiency.

Efficient flight training results in less money and time spent, as well as an overall boost in learning gains over a period. So from every angle, there’s a benefit to the student who finds ways to learn more efficiently. Here are five to get the ball rolling!

1. Preparation

Make it a goal to come prepared. Student pilots who do preparation before their training get more out of their lessons. It makes sense that you have tried to improve your theoretical understanding of flying in between training sessions, you can more or less just work that into practice when you arrive on your training days.

Preparation can mean:

Doing practice radio calls
Studying theory
Knowing the flying pattern
Learning procedures at the training airport

Ask your instructor for details about your next lessons, and for ideas on any extra study that could help you get the most out of it. They will be happy to help!

2. Flight Simulation

Technology has a lot to do with efficiency. If your flying school has a Flight Simulator, you should be making use of it. For the first few lessons of flight training in particular, a Flight Simulator can help you get used to flying procedures. Learning these procedures in the simulated environment first means that time spent in the real cockpit can be used to test this knowledge rather than build its foundation, and it gives you more of an opportunity to hone other aspects of flying.

3. Teamwork

Find a peer to connect with over the course of your flight training. The enthusiasm generated between fellow enthusiasts becomes self-perpetuating and the interaction, both in the air and on the ground, can be highly motivating. If you’re generally quite hard on yourself, this is a great way to get another perspective on the training process and a greater boost from each of your achievements along the way.

4. Reflection

As a student, you should be thinking about the process of flying while on the ground as one of the ways to improve flight training efficiency. This will help you to focus your mind during flight, and get used what to expect and how the flight should progress. It will also help you to get ahead of the aircraft when transitioning to different stages of the flight, such as from take-off to the climb and then cruise.

5. Look for schools offering value

Look for a good flying school with high standards, and when comparing different schools think about them based on the value they offer you. Value doesn’t just mean finding the cheapest course. It combines quality of instruction, aircraft, facilities and of course, pricing. Find out if the school you’re looking at has instructors with a passion for mentoring others, and are not only accruing their teaching hours in order to get into other jobs. High standard flying schools all have one thing in common: they’re there for you, the student!

AL42-Diamond-DA42-Simulator-Learn-To-Fly-Melbourne-Hero
Making good use of flight simulators is a great way to improve flight training efficiency.

Find out how we can improve your flight training efficiency! Email [email protected]. You can also visit https://drift.me/learntofly/meeting to book a meeting and school tour. For more great flying tips and the latest flying videos, click below and subscribe to our YouTube channel!

Learn-To-Fly-Melbourne-Youtube-Subscribe-Footer

Schedule a School Tour

We're here to provide you with more information about learning to fly. If you are in Melbourne, feel free to schedule a school tour to check out our aircraft & facilities. Speak to our friendly flight instructors & staff, they will talk you through the whole flight training process, step by step, and answer any questions you have.

Schedule Now