LTF News Archives

-->

How To Execute A Forced Landing: Case Study (Part 1)

Posted on April 25, 2018October 22, 2021 by Kai

The man who sent me on my first solo flight in Hong Kong is full of wisdom and has a sense of humour in the cockpit. He shared a flying experience involving a forced landing in a Cessna 152 with me. I want to share this story with you now as a case study along with tips that will guide you on how to execute a forced landing.

This is his story:

Tolo Harbour, Hong Kong, Approximately 2,800 Feet

On the 26th of February, like any other Sunday, I was sitting in the flight operation office in Hong Kong. Little did I know, out there in the Tolo Harbour, a Cessna 152 was about to be at the centre of a whirlwind adventure involving a forced landing.

At the time, we were doing some pre-examination exercises for students, and we had just turned around towards the Shek Kong Airfield. The engine suddenly ran rough, so I pulled the carb heat out and went full throttle, but it did not change the situation.

I was thinking, “Is this my lucky day? Alternatively, a bad day?”. But really, you don’t have time to think or even pray.

Decision Time

A decision had to be made in around 10 seconds. I had 3 options.

1. Go back to Shek Kong, but in that case, I would fly over Tai Po and many buildings.

2. Fly over to the dam wall (of the Plover Cove Reservoir), but it was 11.30am on a Sunday which means many people were there.

3. Fly towards Three Fathoms Cove.

I thought of those three options and discarded the first two options as they were too populated. Either way, today was the day for learning how to execute a forced landing.

Altitude

When you are at that height you will have less than two minutes before ground impact. I was thinking, “if I drag on too much or if I drag on too long, I wouldn’t have the altitude to execute my approach.”

At this point, I still didn’t want to believe that I had to do a forced landing, and I always wanted to revive the engine and glide back into the airfield. I asked ATC for approval to climb above the vertical limit, and they said, “Sure, no problem.”

The Engine Will Not Revive Itself. Decision Time Again.

You can’t spend too much time hoping to recover the engine. Run your checklists and if it isn’t working, make the decision to execute a forced landing.

The rule of the thumb here is to get a plan and stick with it. If you keep switching plans and your aircraft keeps descending, you will eventually limit your options for the forced landing too much, which is more likely to have serious consequences.

Forced Landing: Into The Trees On The Golf Course!

So how did I manage to land in the trees of the golf course without injuries? And moreover, why did I choose the trees?

I was trained to approach a field with an escape route to overshoot and go around in case something miraculously happens to the engine. The most important thing is that you have a technique to slow down. I can do S-turns to bleed off the height and shorten the landing distance, and side-slipping helps as well.

I was at 70 knots, nowhere near 60, and I was out of options at the time. If I dived the aircraft into the golf course, I would gather up speed, which may result in a tumble and getting wet. I spotted a relatively flat spot in the trees. I went for it. With full flaps, I hit the trees at around 45 knots, close to the minimum controllable airspeed.

Intentionally, I aimed between two branches so the wings would hopefully lessen the impact. And it did. The left-wing was broken off, but we walked away unhurt.

Head to Part 2 of this case study to see the lessons learnt and gain some tips on how to execute a forced landing. Thanks to LTF student pilot Howard Lau for contributing this case study on how to execute a forced landing.

Execute-Forced-Landing — Making fast decisions is an important factor in how to execute a forced landing.

For information on our flying courses, email [email protected] or go to https://drift.me/learntofly/meeting to book a meeting and school tour. You can also get more handy flying tips by clicking below and subscribing to our YouTube channel!

The Best Flight Instructors Make The Best Pilots

Posted on April 15, 2018October 22, 2021 by Kai

Flight instructors are the backbone of all successful pilots, whether that’s for a career or just flying recreationally. One of the most important considerations you can make when choosing a flight school is finding the one with the best flight instructors.

Here at Learn to Fly, the best flight instructors are training some of the brightest future pilots in Melbourne. Students are assigned primary and secondary flight instructors. However, this can obviously be flexible based on student progress and training requirements. We have a wide range of flight instructors with diverse backgrounds and varied areas of expertise for this very reason.

The best flight instructors will always be the ones you’re able to build a productive and trusting work relationship with. Regardless of how far into your aviation career you are, your instructor should always be someone you can rely on for guidance, assurance, advice and improvement.

Here are five great qualities all aviation students can expect from the right flight instructor:

They Have A Diverse Range Of Experience

Based on CASA guidelines, there are 3 levels of flight instructor for General Aviation. There are Grade 1 and Grade 2, and Grade 3 – with Grade 1 being the most senior. Beyond that, you have RA-Aus instructors and also instructors with specific capabilities such as IFR or multi-engine training.

Grade 1 instructors have extensive experience in not only flying, but also in instructing. To achieve that level of seniority, they have displayed their expertise in teaching both students and other instructors. Typically, your primary instructor at LTF will be a Grade 1 instructor.

It’s important to find a flight school that has instructors of all levels, and with a wide range of additional capabilities. But beyond what’s on paper as far as capabilities go, look for a diverse range of experiences. Our instructors come from multiple countries, and from different areas of aviation including airlines, charter and more.

Your Safety Is Their Priority

A large portion of flight training centres on emergency procedures. Stalls, wing drops, forced landings, engine failures, radio failures, and the list goes on! This is why our school standards require instructors to be not just be well-trained, but for safety to be their first priority.

A focus on safety is learned behaviour. A flight school with high safety standards passes this on to their instructors. The instructors then pass it on to you, the student. By treating EVERY safety detail as important – even the small things – bigger saefty issues become less likely.

The best instructors will respond immediately to any situation in which the risk outweighs the learning opportunity. This may mean that an instructor wants you to repeat something when you want to progress. That might be frustrating at the time, but it will make you a better pilot.

Beyond our instructors, our Chief Flying Instructor (CFI) and Safety Manager actively supervise all flight training operations and consistently check training records and documentation. This ensures compliance with Standard Operating Procedures (SOPs) and means students can always feel safe while flying!

They Bring Out The Best In You

What kind of learner are you?

Do you learn visually or kinesthetically?

Do you like to push yourself out of your comfort zone or take things step-by-step?

Are you goal orientated, or do you prefer to enjoy the ride?

You may not yet know the answers to these important questions. The best flight instructors will help you to learn these answers, and will be able to adjust their teaching style to bring out your best. Sometimes it becomes apparent that your primary or secondary instructors may not be best suited to your learning style. This is another reason why having a diverse range of instructors at a flying school is important.

Aside from the dos and don’ts of flying, an outstanding flight instructor will teach you the right attitude towards managing risks, valuing responsibilities and trusting in your abilities.

They Make You Confident

Confidence and self belief are huge factors when learning to fly. Not everybody is confident in their own abilities, or their own knowledge. It’s a very different feeling being 3000ft up with an experienced instructor next to you, and being up there alone.

The best flight instructors will help you to trust yourself.

It’s also important to ask as many questions as possible when learning to fly, and you should always be confident asking your instructor anything. Even the questions you may think are silly – because really, there are no silly questions.

The best flight instructors are excellent motivators who’ll help you overcome any self-doubts and boost your confidence. Remember – they were a student once too.

They Inspire You

Your teachers are always a part of your story in life. Whatever knowledge your instructors instill will remain long after they leave your side in the cockpit. And it’s this knowledge that you will often look to as your inspiration to fly.

Sometimes, learning can become a chore. You may be struggling to progress past a certain point. You may not find what you’re learning at the moment as exciting as some other areas. Let’s face it – some of that theory stuff can drag – especially when you just want to get airborne!

Whether you want to fly for fun or for a career, a great instructor will inspire your aviation journey. They’ll make you remember what drew you to flying in the first place, and inspire you to fly further and higher.

Find your perfect flight instructor at Learn To Fly. Email [email protected] or visit https://drift.me/learntofly/meeting to book a meeting and school tour.

Airline-Pilot-Career-Specialist — The best flight instructors make the best pilots!

Learn To Fly Becomes The First Diamond DA42 Flight School In Victoria

Posted on April 5, 2018October 22, 2021 by Kai

We are proud to announce that we have ordered the Diamond DA42 aircraft, making us the first Diamond DA42 flight school in Victoria, Australia. The DA42 is an elite twin-engine aircraft equipped with a Garmin G1000 avionics system, produced Diamond factory in Ontario, Canada.

The DA42 will be the first new major multi-engine aircraft type introduced into LTF’s fleet since we started flying the Piper Seminole. This acquisition provides us with the ability to replace our older, less efficient aircraft and deliver better quality training. We believe students should have as many options as possible when it comes to flight training.

Training at a Diamond DA42 flight school in Victoria has many benefits for students. Here are our top five reasons why you should train in a DA42!

1. Amazing Specs & Performance

The twin-engine Diamond DA42 truly is a next-generation aircraft – it combines all the newest innovations to create a capable, robust aircraft that turns heads. The DA42 boasts carbon fibre construction, FADEC controls, glass cockpit with Garmin G100, and a 1000 nautical mile range.

There are very few planes that perform well enough to fly comfortably across the Atlantic at a lower altitude as well as through varied terrain. The Diamond DA42 does that in its sleep.

You will get to enjoy every moment flying, thanks to the panoramic wrap-around canopy and generous rear windows.

2. Advanced Avionics

The Garmin G1000 avionics system is complimented by several avionic options. These can suit almost any need and are usually only available on much more expensive aircraft. The advanced avionics and day and night weather capability offered by the aircraft means that a full variety of flying experiences await.

3. Safety

At Learn to Fly, safety is our priority. It’s only fitting that Diamond aircraft has one of the strongest safety records of any light aircraft in the general aviation industry today. Furthermore, aspiring airline pilots and private pilots alike can enjoy the impressive cross-country performance and safety of the DA42 twin-piston without the additional costs often associated with having a second engine — fuel, maintenance, etc.

4. Environmental Innovation

The DA42 is powered by with eco-friendly, fuel-saving and powerful engines. These engines have far less fuel burn than conventional engines. This dramatically reduces the flying costs for students.

5. Obtain Your Multi Engine Class Rating or MECIR

Thanks to the Diamond DA42, those hoping to become airline pilots can gain considerable experience with similar flight approaches, procedures, and conditions similar to those encountered by light jets and turboprops.

This makes the DA42 one of the best aircraft options when pursuing a Multi Engine Command Instrument Rating especially.

Learn To Fly Is The Only Diamond DA42 Flight School In Victoria

The purchase represents a new chapter for LTF, with the DA42 becoming a valuable addition to our fleet. It will allow students to complete their Recreational Pilot Licence (RPL), Private Pilot Licence (PPL), and Commercial Pilot Licence (CPL) training on the Diamond DA40 and then smoothly transition onto the DA42 for their multi engine training.

We will be ordering more Diamond D40 aircraft and another Diamond DA42 this year. As our flight training fleet expands, so does our capability to train the next generation of pilots.

Want to learn more about flying with the only Diamond DA42 flight school in Victoria? Email [email protected]. You can also visit https://drift.me/learntofly/meeting to book a meeting and school tour.

Flying In Marginal Weather: A Student Pilot Experience

Posted on March 25, 2018October 22, 2021 by Kai

Flying in marginal weather with an experienced instructor is a great way to gain experience and build confidence. As an aviation student, you will regularly be placed in unfamiliar situations that test your skill, airmanship and decision making. These judgements could even determine the entire outcome of a flight. It is paramount for all pilots to attain a weather briefing for all matters of flying, including flying circuits.

The 24th of September, 2017, was a definitive learning curb and monumental day for me in my aviation career. What was supposed to be a regular day of circuit flying soon turned into an unforeseen challenge.

The weather was marginal on that day, with gusts up to 20 knots and some showers, as the outer rainbands of a tropical depression were affecting us here in Hong Kong. However, it seemed safe enough to fly circuits at first glance.

Fly with an instructor who is comfortable with flying in marginal weather

This will allow you to test your limitations safely.

After pre-flight, I immediately requested not to be sent out solo due to the weather. Nevertheless, my instructor and I decided that today would be a wonderful opportunity to test my abilities safely under his supervision.

My instructor was comfortable with the conditions; however, we were both aware of a squall line brewing to the south of Hong Kong that could potentially affect us. We calculated that we had at least 45 minutes before the line hit, and we assumed we would be in the clear.

Think beyond the aviation weather briefing

Interpreting the weather does not stop there. It’s vital that you can visualise how the forecast can potentially affect your flight.

Heels to the floor, full power, RPMs in range, Ts and Ps in the green and as the aircraft passed 55 knots; I gently applied backpressure for a smooth take-off.

Almost as soon as I climbed above the tree-lines, the aircraft jolted to the right, and I corrected instinctively. I remembered exactly how to respond during turbulence – focus on holding the altitude of the plane, don’t chase the altitude and most importantly don’t bust manoeuvring speed.

As I rolled out on downwind, the aircraft was thrown around in all directions. My body, with the absence of double shoulder harnesses, was also thrown around alongside as the rain and turbulence worsened. I struggled but managed to get my pre-landing checks complete and radio call out. Despite my headset bumping the ceiling, in such turbulence, one must remember that the priority is always to fly the aircraft.

Fly the attitudes. It will save your life one day!

The final approach was terrible, the turbulence made me delay my full flaps selection and I felt as if the aircraft was being tossed around. It occurred to me that I was way too flat as I flared so I applied more back pressure to establish a landing attitude. Even so, it turns out that I was way too fast. I hit and bounced, holding the landing attitude before touching down once again. The conditions weren’t easing, and I really began to worry.

The rain and turbulence escalated and my headset fell off. The instructor took over as I tried to collect myself. It appeared the squall line on the radar image I saw before the flight was going to hit. I voiced to my instructor and knew that this was going to be a full stop.

Plan for unforeseen delays. Anything can close the runway

Prepared and eager to land, I rolled out on downwind, least expecting flight operations to declare a runway closure for 5 minutes over the radio.

The rain became menacing as I flew at circuit height and held, pelting onto the windshield, and obscuring my visibility. My instructor, however, remained silent to test my decision-making skills for flying in marginal weather.

Waiting for the all-clear seemed like forever. Panic began to set in as I came too close to losing control. “Don’t chase the instruments and hold the attitude,” I reminded myself.

“The runway is now all clear”

Thank goodness. My instructor sprang into action and decided to help me with radios. On the base leg, I set the appropriate attitude for 75 knots and trimmed—I feel very fortunate to be taught how to fly attitudes instead of chasing airspeed, the emphasis on attitude flying by Learn to Fly helped immensely.

Just as I was about to turn final, 75 knots plummeted to only 65 and I sank like a rock. I just had a wind shear of a 10-knot loss. Immediately I applied full power and performed a go-around.

On final approach, I focused on just flying by feel. The landing was hard; however, being back on the ground was all that mattered.

“A superior pilot uses his superior judgement to avoid situations which require the use of his superior skill” – Frank Borman, NASA Astronaut, Commander of Apollo 8

Fifteen minutes after landing, the squall line came through with heavy thunder and rain. It was at this moment I realised the outcome of today’s flight was merely a testament to my good judgement under pressure in a difficult situation. My instructor and I were both safe after I made the decision to call it off. It reiterated to me that as a student, we have the right to make a no-go decision! Because despite embracing every ounce of optimism, even for the simplest of tasks, it won’t change the weather outcome.

This flying in marginal weather experience strengthened my decision-making skills and confidence as a pilot. Contributed by LTF student Horace Ho.

Passing The Recreational Pilot Licence (RPL) Flight Test

Posted on February 27, 2018October 22, 2021 by Kai

Every professional pilot once undertook and passed their Recreational Pilot Licence (RPL) flight test. You’ve completed your theory and your flight training, and your instructor has told you that you are ready. But what should you prepare for in order to pass the test with flying colours?

On the day of the test, the CASA-approved testing officer will sit with you and run through how they will be grading you. It may seem daunting, but don’t stress, going for and passing your Recreational Pilot Licence flight test really isn’t as scary as you make it out to be. Plus, it’s all based on knowledge and skills that you have already demonstrated.

In-flight, your testing officer will want to see how you can demonstrate the following:

1. Steep turn through 360 degrees and back onto the original heading

The best way to do this is to make sure you give a thorough lookout to ensure you are in the clear before the turn. When you’re ready, hold the required amount of back pressure on the control stick so as to stay more or less the same altitude or level out in anticipation as you come back upon your original heading.

2. Stall recovery

For this part of the test, your testing officer will want you to demonstrate stall in various configurations. Make sure you remember the HASELL checks—Height, Airframe, Security, Engine, Location, Lookout—and know how to identify the symptoms before entering a stall.

Your instructor may also ask you to demonstrate how to recover a stall with a wing drop. If you make sure to use rudder rather than the ailerons, in the opposite direction of the dropped wing, you’ll be fine!

3. Forced landing

An integral part of flying – and your responsibility – is to be prepared for anything. To make a forced landing successfully, maintain control of the aircraft and select the suitable field. It is important to carry out all emergency checks. Conduct the passenger brief and mayday call, and always make sure to reassure the “passengers” that you are a trusted pilot and have been trained to handle emergency situations.

4. Instrument flying

The testing officer will want to see your demonstrated ability to fly on instruments alone under the hood. To do so, ensure you stay within the +/- 100 of the requested altitude and +/- 10 of the requested heading.

5. Circuit flying

The final part of passing your RPL flight test will have you demonstrate how to fly a squared circuit pattern and control your speed and altitude when doing so. Make sure you can also land the plane with different approach configurations, and manage engine failure after take-off and in the circuit.

Remember your inbound radio calls as you return to Moorabbin Airport’s control zone, and congratulations, you’ve completed the test.

After passing the RPL flight test and obtaining their RPL, students are qualified to fly within 25 nautical miles of the departure airport and carry passengers, during daylight in good weather (VFR) conditions.

Remember that every professional pilot was once a student, itching to achieve their next milestone. Bombarding their flight instructors with questions about how many flying hours it would take for them to reach their First Solo, Training Area Solo, RPL, PPL and finally, CPL.

However, we know that while flying itself is a great adrenaline rush, you shouldn’t be in a rush when learning and attempting your exams. If you mess up any part of the RPL flight test, remember that it won’t be the end of the world. You will always be able to have another go.

Student-Pilot-Checklist — Remember your checklists! They are crucial to successfully passing your RPL flight test.

For more information on our RPL course, email [email protected] or go to https://drift.me/learntofly/meeting to book a meeting and school tour. You can also get more handy flying tips by clicking below and subscribing to our YouTube channel!

Aircraft Forced Landing Techniques

Posted on January 25, 2018October 22, 2021 by Kai

A situation that requires a forced landing is something that most pilots would rather not experience while flying. But the reality is, that while uncommon, it could happen at any time. It’s a pilot’s job to be prepared. Like anything, practice makes perfect. In this blog we look at aircraft forced landing techniques.

To complicate things a little, there are a couple of different aircraft forced landing techniques a pilot may be instructed to follow. Knowing them all gives you more flexibility to make the right decision should the need arise. Lets take a look at both the traditional and alternative methods.

Traditional High Key / Low Key Forced Landing Technique

The High Key /Low Key technique is the method traditionally taught in most civilian flying schools across the world. This technique depends on your judgement of the trajectory of the flight in order to hit 1500 feet by your low key position, which is normally abeam your IAP (Initial Aiming Point) on a downwind.

Forced-Landing-Technique-High-Key-Low-Key — The High Key / Low Key method is the most commonly taught of the aircraft forced landing techniques

Some believe this technique to be somewhat flawed. There are a lot of factors to process in order to clearly judge the altitude of your aircraft in a glide at a particular arbitrary point. It also requires the pilot to be extremely knowledgeable about surrounding terrains and the elevation of the terrain they are flying over, which sometimes can be challenging.

Constant Aspect Technique

The Royal Air Force has developed a newer method, known as the Constant Aspect Technique. This method combats the issues of different aircraft, and the requirements for some undetermined judgements.

The principle of this aircraft forced landing technique is that it removes all the guessing of altitude and descent angle. It narrows down to one thing, which is called the “Sight Line Angle” or SLA. It is the perceived angle between the IAP of your landing field and the horizon.

Realistically, all you can look at during the forced landing with this technique is airspeed and the SLA.

Forced-Landing-Technique-SLA — The “Sight Line Angle” or SLA is the perceived angle between the horizon and the IAP of your chosen landing field.

The SLA is the “Aspect” which is part of this entire forced landing approach, and the “Constant” is basically the entire technique itself. The ultimate goal of the entire pattern is to keep your SLA constant as you approach the IAP.

How To Conduct The Constant Aspect Technique

The first step to fly this approach is to pick a landing field within safe gliding distance and meet the criteria set out by your instructor. Next, you can choose a sensible IAP within the first third of your landing field. This will be the “fulcrum” where your aircraft will pivot during the entire pattern, which ideally is a round pattern unlike the High/Low Key method with a rectangular pattern.

Forced-Landing-Constant-Aspect-Technique — The Constant Aspect Technique is one of the newer aircraft forced landing techniques.

Ideally, you will join what is equivalent to a crosswind. However, depending on wind direction, it may be a direct downwind or a midfielder crosswind join into the “circuit”. It is important that your bank angle does not exceed 20 degrees during the approach. Otherwise, you may risk the SLA either increasing or losing airspeed and glide ratio due to the reduced vertical component of lift and increased drag.

If your SLA is increasing (getting too high), deviate from best glide speed or increase spacing.

If your SLA is decreasing (getting too low), decrease spacing, fly inwards.

When approaching final, you must make the turn in to directly approach your IAP. This is the time when you decide, using your knowledge of the trend of your SLA, whether you:

1. Cut in short

2. Fly a standard final, or

3. Overshoot and then turn back onto final depending on your height.

If the SLA is high, you have three options to get back onto glide path. You can use flaps, do S-turns or do a steep slip, or you can combine S-turns and steep slips if it is ridiculously high.

This technique is not only used by RAF but also being slowly accepted by flying schools around Europe and the UK.

It is recommended that everyone should practice the entire pattern all the way down into the flare and touchdown. You will find out, if you really are ridiculously high, you can still hold the slip into the flare, centralise the rudder when the aircraft sinks, and then continue to flare.

Experiment With Aircraft Forced Landing Techniques

Chat to your flight instructor about which method they prefer and why. Proactively seek to practice both aircraft forced landing techniques, so that you know which one you feel more comfortable with.

Thanks to LTF student pilot Howard Lau for contributing this article on aircraft forced landing techniques. For information on our flying courses, email [email protected] or go to https://drift.me/learntofly/meeting to book a meeting and school tour. You can also get more handy flying tips by clicking below and subscribing to our YouTube channel!

Victoria’s First Diamond DA40 Flight Training School

Posted on December 21, 2017October 22, 2021 by Kai

Our first Diamond DA40 has just landed to join our flight training fleet at Moorabbin Airport in Melbourne. This means that we are now officially Victoria’s first Diamond DA40 flight training school.

The arrival of the DA40 continues Learn To Fly Melbourne’s successful expansion over the past year. We have committed to building the state-of-the-art Learn To Fly Flight Training Centre on a new larger site, and have received our Part 142 qualification.

About The Diamond DA40

The DA40 is a reliable and durable four-seater aircraft, made out of lightweight and robust composite material. Powered by a Lycoming IO360 engine, and boasting a spectacular balance between performance and durability, the Diamond DA40 is a brilliant flight training aircraft.

Our DA40 has a Full Authority Digital Engine Control (FADEC) system, helping LTF students secure a seamless transition from RPL all the way through to CPL training. It also makes the aircraft both efficient and economical. This is particularly handy when completing long navigational flights for PPL, and for CPL hour building.

This state-of-the-art aircraft is decked out with both round instrument panels and the Garmin G1000 avionics. The cockpit has plenty of space, with a comfortable and ergonomic design, and excellent visibility.

We plan to order even more DA40s moving forward, further expanding our fleet. It is our goal to give our flight training students as much flexibility as possible.

Diamond DA40 Specs

Engine: Lycoming IO360

Avionics: Garmin G1000

Cruising Speed: 130 Knots

MTOW: 1,150 Kilograms

Wingspan: 11.9m

Landing Gear: Tricycle

Available Diamond DA40 Flight Training Courses

Given its versatility, the Diamond DA40 can be selected for most of our flight training courses. It is perfect for Recreational Pilot Licence, Private Pilot Licence, and Commercial Pilot Licence students. Its Manual Pitch Propeller Control (MPPC) means that we can now offer this as a design feature endorsement. The DA40’s Garmin G1000 means that it is also equipped for Instrument Ratings.

In addition to this, we have plans to order the DA40’s twin-engine sibling, the Diamond DA42, for multi-engine training. This will provide our students with an even more seamless transition from single engine training to multi engine training. Stay tuned!

Dimaond-DA40-Flight-School — Learn To Fly has become the first Diamond DA40 flight school.

Want to learn more about flying with the only Diamond DA40 flight school in Victoria? Email [email protected]. You can also visit https://drift.me/learntofly/meeting to book a meeting and school tour.

How Flying Critical Incidents Can Occur

Posted on November 24, 2017September 7, 2021 by Kai

When an aircraft flying under Visual Flight Rules (VFR) enters Instrument Meteorological Conditions (IMC), flying critical incidents can sometimes occur. In most cases, this is due to reduced visibility or inadvertent entry into clouds. Both of which happen because of the loss of the natural horizon.

Unfortunately, such flying critical incidents have cost the lives of many pilots.

You hope it will never happen to you

Before I began my pilot journey, I always seemed to find the time to read unfortunate accident reports where a non-instrument rated pilot on a VFR flight enters IMC. It is even more unfortunate to realise that many of these incidents become fatal accidents. The more I’ve read, the more I’ve tried to make myself believe, ‘It will never happen to me!’

For non-pilots, all of these accidents seem preventable. Reading the Terminal Area Forecast (TAF) and good weather knowledge are all valid and effective strategies to combat any similar occurrence from happening. However, today I will write about a time when this happened to me on a training flight, nonetheless with an experienced instructor on board.

Before undertaking the task of writing it, I had been wondering about whether or not I should really share my story. However, I made the decision to do so knowing it could help educate other pilots and student pilots about when flying critical incidents can occur.

Cloudy conditions and lower visibility

It was a very cold morning after a cold front came through the day before. I checked the METAR of Hong Kong International Airport and the forecast indicated cloud covers clearing and rising to 2500 feet with 9 kilometres of visibility. However, as I arrived in the flight operations office, we received PIREPs from other pilots of temporary visibility reduction to an estimate of fewer than 3 kilometres near the high ground. I knew this could become an issue upon exiting the airfield area into the training area via a gap in the mountains.

The aircraft from previous slots were rocking the circuit and about to finalise their return. Skies above Shek Kong Airfield were clearing and let in some warm sunlight. However, the area towards the exit route (Kadoorie Gap) into the training area was still rather cloudy. I saw clouds on the other side of the mountains and thought this could really be an issue for our flight today – we had some instrument flying planned.

Climbing to 1500 feet

My instructor had nearly 40 years’ experience in the UK as an aerobatic pilot and warbird pilot. He also holds an Instrument Rating – Restricted on his CAA license – although on his Hong Kong license he does not hold such rating. Even so, his instructor rating allows him to teach basic instrument flying and tracking. On this day, despite the clouds, I put my trust in his judgement and was well aware of his capabilities since we had flown together numerous times.

We taxied out to the runway after our run-up checks, only to notice something very strange. Our slot was supposedly fully booked out with our entire fleet expected to fly. However, there was no action on the aircraft apron. I recall looking to my right as I prepared to shift into full power for takeoff and witnessing all the aircraft sitting idly, waiting for the weather to clear. Still, I thought there was no time to waste and we took off.

We climbed to 1500 feet and tracked towards the exit. As soon as we switched frequencies for traffic information service we heard a rescue helicopter saying, “Visibility deteriorating to less than 3000 meters.” I wasn’t sure where the helicopter was, but in retrospect, it really should’ve been the warning to turn back. We pressed on and exited out of the mountain gap and went on to “the other side,” where all the nasty clouds were, maintaining 1500 feet all the way through.

Scary in-flight sights

As soon as the mountains disappeared from my peripheral vision, my instructor and I realised that visibility was not 9 kilometres, as we had initially projected, and I could only see what was in front of us by looking downwards.

The only visibility I had was of the ground below, including the roads, trees and buildings of Tai Po. I looked back and realised that our only escape route back to the airfield would be obscured if we kept going. Just as I was about to turn back, it became apparent that my instructor had the same idea in mind. “Bring us back,” he said.

Returning through the mountain gap

The direction indicator on that particular Cessna 172 was somewhat defective. This meant I started my timer on my watch and began a rate one turn to the left. I timed for 1 minute, which at 3 degrees a second would be a full 180-degree turn. Fortunately, the mountain gap remained in view this entire time and I instinctively throttled up to return quickly. We were pushed even lower as we entered the airfield airspace, finally descending to 1300 feet. It was very uncomfortable watching the mountains on either side of me come so painfully close.

Lessons learnt

Of course, we were fortunate that despite this being a VFR into IMC incident. The visibility was still sufficient for a safe turn-back manoeuvre.

Among the contributing factors to the success of this was the expertise of my instructor, who holds a restricted instrument rating in the UK, and the fact that at this time I had already completed an hour of instrument flight training. A serious lesson in how flying critical incidents can occur.

After landing, and during the debrief, we narrowed the causes down to the ‘get-there-itis’ that occurred as a result of wanting to squeeze more instrument flying time in for me and also the fact that my instructor was instrument-rated and we put such confidence in his expertise. In retrospect, we shouldn’t have even left the ground in the first place.

This flying incident is proof that pilots with any amount of experience can be sucked into this veil of complacency. They then can make decisions which go against rational and safer judgement. It is an incident my instructor and I will both go on to remember.

Safe flying everyone!

Thanks to LTF student pilot Howard Lau for contributing this article on how flying critical incidents can occur. For information on our flying courses, email [email protected] or go to https://drift.me/learntofly/meeting to book a meeting and school tour. You can also get more handy flying tips by clicking below and subscribing to our YouTube channel!

Five Benefits of Choosing a Part 142 Accredited Flying School in Australia

Posted on October 5, 2017June 26, 2024 by Kai

Learn to Fly Melbourne is excited to announce that we have become a Part 142 accredited flying school operator under the Civil Aviation Safety Regulation (CASR). This results from our new partnership with Australian Pilot Training Alliance (APTA).

Over the past few years, pilot licencing regulations in Australia have been reorganised and redeveloped. They have changed from older criteria to reflect a more global perspective regarding pilot licencing and standards.

This move may not be obvious to the customer or pilots. Yet it has given rise to new terms and extra regulations and definitions. Flight training organisations across Australia now have two main paths that they can follow when seeking to earn their air operator certificate: Part 141 and Part 142.

Why choose a Part 142 accredited flying school in Australia?

Less than 5% of flight schools in Australia have received the advanced Part 142 flight training qualification. This accreditation means that we can continuously expand our flight training operation to reflect the highest industry standard.

There are numerous benefits for students, pilots and instructors who fly at a Part 142 accredited flying school.

1. CASA Approved Syllabus

Part 142 organisations must provide a Civil Aviation Safety Authority (CASA) approved syllabus of training. This CASA approval caveat for Part 142 initiates the necessity for additional oversight of training programs within organisations.

This results in further internal development and higher levels of safety and training. That subsequently improves standards not just within individual organisations but also within the wider aviation community. Part 142 flying schools benefit from a consistently higher level of governance and checks from CASA.

2. Advanced Flight Training

Our comprehensive CASA approved flight training syllabus includes the following new courses and types of flight training:

Integrated flight training for Private Pilot Licence (PPL) or a Commercial Pilot Licence (CPL) courses

Multi-Crew Pilot Licence (MPL), Air Transport Pilot Licence (ATPL) and Flight Engineer Licence

Multi-Crew Cooperation (MCC) training

Contracted recurrent training and checking

Being able to offer integrated flight training is one of the major points of difference between the Part 141 and Part 142 qualification. What it means for students earning their CPL is that they can cut down their flight training hours from 200 to 150 – a 50-hour flight training discount when compared with Part 141 flying schools.

3. Increased Cost Effectiveness

Integrated flight training – Our 150 hours Integrated CPL syllabus which blends practical flying and theory-based training compared with the 200 hours CPL syllabus offered by other Part 141 schools – is just one of the ways that the Part 142 qualification is extending our commitment to provide students with cost-effective flight training.

4. Internal Training & Checking

Part 142 flight training organisations are required to have a professional development program for all personnel and flight instructors within the school. They must also have a quality assurance manager to ensure ongoing high standards.

This conditional improvement of know-how and standards applies not just to students, but trainers and instructors alike who continually develop their own skills within an organisation.

5. Enhanced Safety

All Part 142 flight training organisations must have:

A Safety Department & Safety Management System

A CASA Approved Safety Manager & Deputy Safety Manager

A Risk Management System

Regular safety meetings, audits and reviews

Safety oversight globally has become one of the main areas of focus in not just maintaining high aviation standards, but improving safety as a whole. This is most visible in the incorporation of formalised procedures for Safety Management Systems.

These systems actively monitor standards and safety within training organisations by promoting an ongoing awareness, attitude and approach towards threats and risk on a daily basis. The net result for pilot candidates is that these systems set a higher standard for all who come in contact with them, making not just the individual pilots safer, but organisations and the industry as a whole.

We are excited for students to enjoy the increased benefits of training with us now that we have achieved the CASA approved syllabus Part 142 qualification.

Want to learn more about the benefits of flying with a Part 142 accredited flight school? Email [email protected]. You can also visit https://drift.me/learntofly/meeting to book a meeting and school tour.

Pilot and Aircraft Safety at Learn To Fly

Posted on August 31, 2017August 15, 2022 by Kai

At Learn to Fly, pilot and aircraft safety is and always will be our number one priority. It is the cornerstone of our operation, and we strive to maintain a positive and transparent safety culture. We continue to uphold an impeccable safety record as conveyed on the Recreational Aviation Australia (RAAus) Accident and Defect Summaries.

The safety culture at Learn to Fly acknowledges that flying and flight training involves risk. It’s vital that students and instructors alike are educated about these risks and the processes involved in risk minimisation.

See how we carry out pilot and aircraft safety in our flight training operations at Learn To Fly.

Aircraft Maintenance

Each aircraft requires maintenance checks for every 50 and 100 hours of flying. All scheduled maintenance is planned in advance. We will never undertake any flights or flight training on planes requiring maintenance.

Pilots and engineers can write up a defect on the aircraft’s Maintenance Release (MR) at any time. For serious defects, the aircraft will immediately become unserviceable and simply will not go flying until maintenance is completed.

The Maintenance Release is required to be signed by a pilot (instructor or pilot certificate holder) before the first flight of each day to ensure that the aircraft has passed the daily inspection requirements and is suitable to fly.

Instructor Qualifications

Pilot and aircraft safety for us also means company standards require that instructors at Learn to Fly be well-trained. We will only employ instructors who we are confident, focused, alert and ready to respond immediately to any potential situation where the risk outweighs the learning opportunity.

Based on the current guidelines, all of our flight instructors are at an RAAus senior instructor level. This rating can only be achieved if the pilot accumulates certain flight training experiences and passes a flight test that is conducted by external RAAus certified flight testing officers.

Some of our students may become junior instructors when they graduate. However, it is a compulsory requirement that they are supervised by senior instructors when they work at the school.

In addition to this, our chief flying instructor (CFI) actively supervises all flight training operations and consistently checks training records and documentation. This ensures that Standard Operating Procedures (SOPs) are complied with for both instructors and students. SOPs compliance is checked at various times. This is usually by attending flights with students to confirm SOPs are maintained, and ensuring all instructors have current qualifications.

Flight Training

We ensure a safe learning environment every time. A student will not fly if the weather is not suitable for that particular lesson. For solo flights, these standards will be even stricter and reflect considerations such as turbulence, wind speed, daylight, student’s abilities etc so that we can provide

Before all flights, the aircraft will be thoroughly inspected. This ensures all controls are functional, check for obvious damage to the engine, airframe or structure before any flight is to take place. After engine start and prior to takeoff further checks are carried out as per the SOPs. This is recommended by both the aircraft manufacturer and in the aircraft’s Pilot’s Operating Handbook (POH) to further assure a safe and efficient flight takes place.

Each student’s flights are recorded in detail. Instructors will rate their performance to make sure students reach the standard or competency of that particular lesson. Students who do not meet these standards or competencies will have to redo the lesson sequence until this standard is met. Within the school, we have systems in place to cross-check and ensure that all training records are completed and updated in a timely manner.

Briefings are always done properly and consistently before and after each flight. This ensures that students are both aware of what they are going to do, and of the specific standard that is required for that particular lesson.

Prior to solo flights, instructors will double-check to make sure the students have all the required documents such as a medical certificate, student pilot licence etc. Training records must also show they have achieved all the necessary competencies prior to undertaking any solo operations.

Creating a Pilot and Aircraft Safety Culture

Further to the priorities and procedures outlined, we maintain our own Risk Management Plan and Safety Management System. This enables us to further minimise the potential risks associated with flight training. Despite this comprehensive system, we must not think that we are infallible. We encourage all of our staff and students to form a habit of looking, learning, and discussing potential risks we see as part of our normal day to day operation. This attitude allows us to evolve and update our systems regularly. That then helps to ensure a safe operating culture persists within the Learn To Fly organisation and group.

We encourage instructors and students to go through appropriate channels to advise safety concerns within or outside of our operation.

We believe that technology as a communication tool has great potential to assist safety operations. Flight training software can provide updates on aircraft unserviceability or if an aircraft may need to be grounded; through to communicating safety concerns or topics that instructors or students raise within the organisation.

Exceeding Expectations

We aim to have higher safety standards than other flight schools in Australia.

On top of the Public Liability Insurance and the RAAus Member Liability Insurance, we cover an additional A$5 million in Liability Insurance for all of our students.

We only buy brand new RA-Aus aircraft so we can be certain of the maintenance history for every plane.

All RA aircraft in our fleet is equipped with Rotax engines which have an outstanding reputation and operational safety history.

At Learn to Fly, we believe all these extra steps – combined with the safety culture exhibited by our individual pilots, instructors, and the student group – will allow us to go a long way in providing an extra margin of safety.

Want to fly with us? Email [email protected]. You can also visit https://drift.me/learntofly/meeting to book a meeting and school tour.